12V Stereo Amplifier Circuit by BA5417 IC
BA5417 is a dual OTL monolithic power IC with two built-in, high output
speaker amplifier circuits. High output of 5W×2 can be produced when
VCC=12V and RL=3Ω, and 2.8W×2 when VCC=9V and RL=3Ω. BA5417 not only
exceeds basic characteristics, but also has a built-in soft clip
circuit, thermal shutdown and standby circuits.Stereo Power Amplifier...
TDA2006 - 12W Audio Amplifier Circuit
This amplifier circuit is build around the tda2006 integrated circuit
who features a short circuit protection system, and a thermal shutdown
system in case of overheating. With a 12v power supply the circuit
delivers 12w on a 4 ohm speaker and 8w on a 8 ohm speaker. The
integrated circuit can work with a power supply between 6v and 15v max.
Skema...
TDA1010 - 10W Audio Amplifier Circuit
This audio amplifier Circuit is a class-B audio power amplifier using a
TDA1010. It is easy to construct and has only a few external components.
The circuit is designed with short circuit and thermal protection. It
can drive loads as low as 1.6 ohm and is capable of deliveringover 10
watts from a 16 V DC power supply.
Skema Rangkaian 10W...
TDA8560Q - 40W Stereo BTL Car Amplifier Circuit
Approached scheme is simple, few external electronic components, is
suitable for construction of car audio. Output power is 2 - 4 Ohm to 2 x
30 W (maximum 2 x 40 W) on two channels BTL (SETREO)Pin Arrangement
and functziile met. Circuit pins are placed on two rows. Bridge
amplifier working so not linked to car speakers table! The integrated...
TA8210AH - 2 x 22W BTL Car Amplifier Circuit
This is a circuit of 2 x 22 watt BTL amplifier using IC TA8210AH. It is
not only an auto amplifier, ideal for a low-frequency auditory approach
those hi-fi, with a very good linear feature. Can be fueled by a 12
volt car battery but shi from a 12 volt charger. The chip incorporates
four bridge amplifiers available in two by two in order...
TDA7375 Car Audio Amplifier Circuit
The following circuit shows about 35W quadruple amplifier and 2 x 25W
bridge amplifier based on the TDA7375 IC, this circuit requests the
minimum of external components. Although the first conception went to
car applications , to give him/it in a great variety of applications of
low potency. That integrated circuit is ideal in the situation...
4 x 25 W Car Amplifier TDA7381 Circuit
This is a 4 x25 Watt audio amplifier circuit using IC TDA7381. The
amplifier circuit require few external components and is very easy to
build. This amplifier is designed for car audio system, but you may use
the circuit for another application such as mp3 player, computer etc
Rangkaian 4 x 25 W Car audio AmplifierUsing TDA7381TDA7381...
DA1553CQ - Car Audio Amplifier 2 x 22 Watt Circuit
This is a 22 Watt car stereo audio amplifier. The circuit is based by a
single IC TDA1553 with some external components, this IC will handle
your stereo car audio system. The IC TDA1553CQ contains 2×22 W
amplifiers with differential input stages and can be used for bridge
applications.. The gain of each amplifier is fixed at 26 dB. The...
TDA 7053 Stereo Audio Amplifier Circuit
Rangkaian 1W Amplifier TDA 7053This is a 1 watt stereo audio
amplifier circuit using IC TDA 7053 from Philips. It is particularly
suited to battery operation, providing 1 watt per channel from only a 6V
DC supply. It will operate best from 6 – 12 V DC and requires no
heat-sink for normal use.Rangkaian TDA 7053 Stereo Audio AmplifierThe...
LM1877 - 2W Stereo Amplifier Circuit
Using the LM1877 chip can be designed a very simple audio amplifier
circuit for small audio applications like portable devices . This audio
amplifier circuit capable of delivering 2 Watt per channel continuous
into 8Ω loads.Rangkaian Stereo Amplifier 2W (LM1877) The LM1877 is a
monolithic dual power Amplifier designed to deliver 2W/channel...
LM4752 - 11W Stereo Amplifier Circuit
Stereo Audio Amplifier circuit using LM4752 capable of delivering 11W
per channel of continuous average output power to a 4 load, or 7W per
channel into 8 using a single 24V supplyRangkaian Stereo Amplifier 11W
(LM4752)The LM4752 is specifically designed for single supply operation
and a low external component count. The gain and bias...
TBA810 - 7 Watt Audio Amplifier Circuit
Here’s a circuit of 7 Watt audio amplifier that is very simple and very
easy to build. This amplifier is built using TBA810 as the main
component with the support of a few passive components. This circuit can
work well, kits and components of this circuit can be found easily at
an electronics store in your area.Rangkaian TBA810 - 7 Watt...
TA7227 - 5Watt Stereo Audio Amplifier
This is a 5 Watt stereo audio amplifier circuit, built based on single
amplifier TA7227 chip. The TA7227 can be used for dual mode (stereo)
and single mode (bridge/mono). This IC type featured some circuit
protection: thermal protection, over voltage protection, current
limitter and BTL DC short connection.Rangkaian TA7227 Stereo Audio...
Rangkaian TDA1554 Audio Amplifier 2 x 22W BTL
Audio Amplifier Based TDA1554 IC This audio amplifier circuit works up
to 2 x 22Watt with main power IC TDA1554. The circuit has only very few
components and works best with a 4 Ohm speaker.IC TDA1554 must be
connected to a heat sink. A computer cabinet fan can also be used in
addition. Any way better the cooling better the performance.The...
TA8215 Car Audio Amplifier 15W BTL Stereo
Rangkaian TA8215 Car Audio Amplifier This is circuit of 15W BTL stereo
channel audio power amplifier based IC TA 8215 developed by Toshiba. In
this power amplifier circuit, two TA 8215 ICs are used. This is for
obtaining four channels that is two channels from each IC. TA 8215 is an
IC with power amplifier stages and preamplifier integrated...
12 Volt Audio Amplifier Menggunakan Transistor
Rangkaian 12 Volt Audio AmplifierThis circuit power amplifier was
deliberately designed using no ICs and in a rather old-fashioned manner
in order to obtain good harmonic distortion behavior and to avoid hard
to find components. The amplifier(s) can be conveniently supplied by a
12V wall plug-in adapter. Closing SW1 a bass-boost is provided...
12 Volt Audio Amplifier IC TDA7222AP
12 Volt Audio Amplifier Used IC TDA7222APThis is the circuit diagram of a
6W audio power amplifier using the IC TA7222AP. IC TDA7222AP is an
excellent integrated audio amplifier which can deliver 5.8W to a 4 Ohms
load at 12V supply voltage. The IC has very good features like, muting
function, low distortion, high ripple rejection, short...
Car Amplifier With Active Crossover
150W amplifier circuit car is equipped with Active Crossover and this
circuit using the chip that has a 4-channel power amplifier. Active
Crossover function is used to separate the tone of the bass, midrange
and treble, the output of direct Active Crossover can be strengthened by
the power amplifier.Power Chip 4-channel amplifier in use...
6 watt Stereo Amplifier IC LA4440
There is a 6 watt Stereo Amplifier based IC LA4440. This circuit very
simple because uses very less components other than the IC LA4440.
Skema rangkaian stereo amplifier IC LA4440
Features IC4440:
Built-in 2 channels (dual) enabling use in stereo and bridge amplifier
applications.
Dual : 6Watt *2 (typ.)Bridge : 19Watt (typ.)
Minimun number...
19 Watt Bridge Amplifier IC LA4440
Here is a circuit Bridge 19 watt amplifier using IC LA4440 from
Sanyo.It uses very less components other than the IC LA4440.A very high
quality circuit with respect to its cost.Skema rangkaian 19 watt bridge
amplifierComponent ListU1...................IC
LA4440R1...................2K2RV1.................PotensiometerC1...................100nFC2,...
Tidak ada komentar:
Posting Komentar